How should manifold, threaded, and barbed versions be selected?

Manifold versions suit valve-bank integration, threaded versions suit M6 or 1/4-28 UNF fitting connections, and barbed versions suit tubing connections and low-pressure fluidic switching.

How should EPDM, FKM, and FFKM diaphragms be selected?

Select based on the reagent, wash fluid, temperature, service life, and chemical compatibility. EPDM can be evaluated for conventional aqueous fluids; FKM or FFKM may be considered where higher chemical resistance is required.

Is an energy-saving circuit required?

If the valve must remain energized for extended periods, consider an energy-saving circuit. For short switching cycles, confirm the configuration based on the control timing and power requirements.

6010 Series Solenoid Valve

6010 Solenoid Valve is designed for low-pressure fluidic on/off control in automated analytical instruments, including reagent, wash-fluid, diluent, and waste-fluid paths. The series uses a swing-arm diaphragm valve and is available in manifold, threaded, and barbed configurations. Its operating pressure range is -75 kPa to 0.25 MPa; the orifice diameter is 1.4 mm, the valve-chamber volume is 20 µL, and the flow coefficient is CV 0.03. For selection, confirm the number of ports, valve configuration, interface type, diaphragm material, fluid compatibility, rated voltage, and need for an energy-saving circuit.

Typical Applications:

reagent on/off control, wash-fluid control, waste-fluid control, valve-manifold integration, sample-probe cleaning, low-pressure fluidic switching

Model:This product is custom-made

Working Fluid	Air, water, deionized water (purified water), diluent, and wash fluid
Valve Configuration	Swing-arm diaphragm valve
Operating Pressure Range	-75 kPa to 0.25 MPa
Orifice Diameter	1.4 mm
Response Time - Standard Version	≤15 ms (without load)
Response Time - Energy-Saving Circuit	≤25 ms (without load)
Maximum Pressure Rating	0.38 MPa
Operating Ambient Temperature	0–50 °C
Working Fluid Temperature	0–50 °C (unfrozen state)
Valve-Chamber Volume	20 µL
Diaphragm Material	EPDM, FKM, FFKM
Rated Voltage	DC 12/24 V (±10%)
Coil Insulation Class	Class F
Power Consumption - Standard Version	2.5 W (0.11 A)
Flow Coefficient (Cv)	0.03

2D Drawing Not Available Yet

To request a 2D drawing for this product, please click “Add Drawing” above.

Datasheet not yet available

The datasheet for this product has not been uploaded yet.

Frequently Asked Questions

The 6010 series is suited to reagent on/off control, wash-fluid and waste-fluid control, sample-probe cleaning, and small valve-manifold integration. It is commonly used in IVD and automated analytical instruments.

requiresconfirm 6010 Solenoid Valve, and ?

fluid, pressure range, port type, NO/NC/, material, and whetherrequires, FOREACH confirm 6010 Solenoid Valve.

Contact an Engineer

Working Fluid

Air, water, deionized water (purified water), diluent, and wash fluid

Valve Configuration

Swing-arm diaphragm valve

Operating Pressure Range

-75 kPa to 0.25 MPa

Orifice Diameter

1.4 mm

Response Time - Standard Version

≤15 ms (without load)

Response Time - Energy-Saving Circuit

≤25 ms (without load)

Maximum Pressure Rating

0.38 MPa

Operating Ambient Temperature

0–50 °C

Working Fluid Temperature

0–50 °C (unfrozen state)

Valve-Chamber Volume

20 µL

Diaphragm Material

EPDM, FKM, FFKM

Rated Voltage

DC 12/24 V (±10%)

Coil Insulation Class

Class F

Power Consumption - Standard Version

2.5 W (0.11 A)

Flow Coefficient (Cv)

0.03